Manual Do Roteador Zinwell G220 Em Portugues Manual Do Roteador Zinwell G220 Em Portugues >>>CLICK HERE. Download >>Download Manual zplus g220 gildan Read Online >>Read Online Manual zplus g220 gildan 13 May 2005 8. Press “Next>>” button then set the IP address.

• Wireless LAN Device Series Multi-Mode AP ZWA-G880 User’s Manual. • TABLE OF CONTENTS NOTICE....4 PREFACE....6 CH 1. ZWA-G880 INSTALLATION...7....7 ACKING...7 ACK PANEL CONNECTIONS...8 ARDWARE NSTALLATION CH 2. FIRST TIME CONFIGURATION...9...9 EFORE TART TO ONFIGURE...9 NOWING THE ETWORK PPLICATION...29 ASIC ETTINGS...32.

• DHCP S...62 ONFIGURING ERVER...63 ANDWIDTH ONTROL S (Q )...63 UALITY OF ERVICE...67 TATIC OUTE ETUP...68 YNAMIC OUTE ETUP VPN P...69 THROUGH CLI M...69 SING...71 YSTEM ANAGEMENT SNMP A....71 GENT...74 ISCELLANEOUS ETTINGS...75 ATCH....76. • Notice FCC Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions：. • CE Statement Hereby, ZINWELL, declares that this device is in compliance with the essential requirement and other relevant provisions of the R&TTE Directive 1999/5/EC.

This device will be sold in the following EEA countries：Austria, Italy, Belgium. • Preface This guide is for the networking professional who installs and manages the Zinwell ZWA-G880 product hereafter referred to as the “device”. To use this guide, you should have experience working with the TCP/IP configuration and be familiar with the concepts and terminology of wireless local area networks. • Power Adapter RJ-45 Cable Back panel connections From Left to Right: DC jack: ZWA-G880 can use power source in DC jack. Please supply the power in 5V and 2A WAN/LAN: This port could be WAN or LAN port depending on the.

• It will be WAN port in router mode and LAN port in bridge mode. LAN: This port is always LAN in ZWA-G880.

In Bridge mode, it bridges to WLAN and “WAN/LAN” port. In Router mode, it bridges to WLAN only, In WISP mode, it bridges to “WAN/LAN”.

First Time Configuration Before Start to Configure There are two ways to configure the device, one is through web-browser, and the other is through Secure Shell CLI interface. To access the configuration interfaces, make sure you are using a computer connected to the same network as the device.

• device can act as AP/Client/WDS. The operation mode is about the communication mechanism between the wired Ethernet NIC and wireless NIC, the following is the types of operation mode. Router The wired Ethernet (WAN) port is used to connect with ADSL/Cable modem and the wireless NIC is used for your private WLAN. Scarface Game Xbox 360. • WDS (Wireless Distribution System) This mode combines up to 8 AP to a single wireless network; the device forwards the packets to another AP with WDS function. When this mode is selected, all the wireless clients can’t survey and connect to the device.

The device only allows the WDS connection. • Examples of Configuration This example demonstrates how to set up a network with different device configurations. There are 2 DHCP servers (DEV1/DEV4) in the network to control the IP configuration of 2 domains (192. Huawei Modem Firmware Backup. 168.2.x/192.168.3.x). Once the setting is done, all the PCs can visit Internet through DEV1. We assume all the devices keep the factory default setting. • Press “Next>>” button then set the “Operation Mode” to “Router” mode. Press “Next>>” button then disable “Time Zone” function.

Press “Next>>” button then set the IP address of LAN interface. Press “Next>>” button then select the “PPPoE” for “WAN Access Type” and fill in the “User Name”. • Press “Next>>” button then select the “AP+WDS” for “mode” and change the SSID to “DEV1”. Press “Next>>” button then select “None” for “Encryption” then press “Finished” button.

Wait for refreshing web page. Use “WDS Settings” page to configure WDS. Enable WDS function and add the BSSID of DEV2 to “Current WDS AP List”. Since we access the device by wireless connection, it may temporarily disconnect when applying the WDS setting. After re-connecting to the device, use the “Status” page to check the settings. • Configure DEV2: Access the web server (of device from the Ethernet port. Caution If you configure multiple devices in the same PC, since the devices have the same default IP address but different MAC addresses, it may cause you not able to access the web server of device.

If the situation happens, please try to clean the ARP table of your PC by DOS command “arp –d”. • Press “Next>>” button then set the IP address of LAN interface. Press “Next>>” button then select the “AP+WDS” for “mode” and change the SSID to “DEV2”. Press “Next>>” button then select “None” for “Encryption” then press “Finished” button. Wait for refreshing web page.

• Access the web server by new IP address “192.168.2.202” then use “LAN Interface” page to disable DHCP Server. Wait for refreshing web page. Use “WDS Settings” page to configure WDS. Enable WDS function and add the BSSID of DEV1 to “Current WDS AP List”. Use the “Status” page to check the settings.